 |
| 数量： | |
|---|---|
WDR-8000CS
万达
产品描述
WDR-8000CS主要技术参数：
项目item | 单位 unit | 参数值 Parameter value | 备注 remark | |||
公称压制力 Nominal pressing force | kN | 80,000 | 可调 adjustable | |||
滑块最大回程力 Maximum return force of the slider | kN | 2000 | 可调 adjustable | |||
主缸最大工作压强 Maximum working pressure of master cylinder | bar | 800 | 可调 adjustable | |||
立柱净间距(框架净间距) Clear spacing of columns(frame clear spacing) | mm | 1500 | ||||
动梁速度及步进量 Moving beam speed and step amount | 最大空程下行速度（动梁从最高位到接触工件） Maximum down speed in the air(Moving beam from highest position to contact workpiece) | mm/s | 150 | 可调adjustable
| ||
最大压制速度（工进速度） Maximum pressing speed(work rate) | mm/s | 15 | 可调 adjustable | |||
单次点动步进量 Single click step amount | mm/s/次 | 0.1-6.0 | 可调 adjustable | |||
最大回程速度 Maximum return speed | mm/s | 150 | 可调 adjustable | |||
动梁最大行程 Maximum travel of moving beam | mm | 600 | 可调adjustable
| |||
压机最大开口（高度向装模空间） Maximum opening of press(height loading space) | mm | 1,400 | ||||
上，下装模垫板长X宽 The upper and lower die pads are long X wide | mm×mm | 1500*1500 | ||||
上、下工作台长X宽 Upper and lower workbench length X width | mm×mm | 1500*1500 | ||||
压机横向操作空间 Horizontal operation space of the press | mm | 1500 | ||||
动梁导向方式 Moving beam guide mode | 1. 快速缸导向；2.X导轨导向(2种并用) 1. Fast cylinder guide; 2.X guide guide (2 kinds together) | |||||
下装模面离地面高度 Height of the bottom die surface from the ground | mm | 1. 打地基600mm；2.不打地基1710mm 1. Foundation 600mm; 2. Do not lay foundation 1710mm | ||||
主机高度 | Height of main engine | mm | 约7000mm About 7000mm
| |||
锻件最高温度 Maximum forging temperature | ℃ | 500 | 甲方要求Requirements of Party A | |||
是否配模具隔热板 Whether to equip mold heat insulation board | 有 Yes | 上下各1件 One from top to bottom | ||||
装机功率 Installed power | kW | 59.7x6+7.5 | ||||
整机重量 Machine weight
| Ton | 约160 About 160 | ||||
动梁控制方式 Moving beam control mode | 1. 磁栅尺； 2.压力传感器(2种并用) 1. Magnetic grid ruler; 2. Pressure sensor (2 kinds of combined)
| |||||
压机操作方式 Press operation mode | 移动操作台 Mobile console | |||||
主油缸驱动方式 Master cylinder drive mode | 液压伺服驱动 Hydraulic servo drive | |||||
是否需要防飞溅安全保护系统 Whether a splash protection system is required | 需要 Yes | 机台自身配置有安全防护门 The machine itself is equipped with safety protective doors | ||||
是否有配置光栅 Whether a raster is configured | 有 Yes | 前后各1套 One set before and one set after | ||||
是否需要顶部维护平台 Whether a top maintenance platform is required | 需要 Yes | 有配置configured | ||||
压机满载时的受载区域当量投影直径 Equivalent projected diameter of the load area of the press at full load | mm | 最大1500 Max. 1500 | 材料质量而定 Material quality depends | |||
压机抗偏载能力 Anti-biased load capacity of the press | 最大直径500 Max diameter 500 | 以梁板中心为半径中心点 The center of the beam plate is the center point of the radius | ||||
压机立柱需要安装显示屏 A display screen must be installed on the press column | 有 Yes | 在移动操作台或电箱上 On a mobile console or electrical box | ||||
压机需具有暂存生产数据功能 The press must have the function of temporary storage of production data | 有 Yes | 触摸屏上有自动存储功能 The touch screen has an automatic storage function | ||||
液体工作压力 Working liquid pressure | bar | 800/180 | 可调 adjustable | |||
